top of page

The Laserworld PRO-800RGB is a white light RGB laser light system with analog modulation and a total output power of up to 800 mW. It is not only equipped with fast scanners for great projections, it also comes with the super bright 637 nm red, that is visible several times better than the 650 nm plus has a thinner, more accurate beam profile. Therefore the Laserworld PRO-800RGB ensures great visibility and is suitable for the beam as well as for graphics projections.

This show laser light provides an analogue modulation. It means a better colour fading and a much broader colour hue. These facts make the Laserworld PRO-800RGB ideal for all applications requiring many different colour hues and colour fadings.

The very advantage of the projectors of the Proline Series is the integrated Glass Effects Actuator: The systems not only run in normal scanner mode. Similar to an optical bench they are equipped with additional grating effects. Without the effects, it is possible to show emotionalizing beam shows as well as graphics projections. Through DMX control three different grating effects can be chosen:

Integrated Effects:

The integrated effects can be used individually through selecting them at the display on the back panel or with a DMX controller, in addition, all integrated effects can be used through Stand-alone Mode or Sound-to-light Mode including in conjunction with ILDA software for spectaculars results

This laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX to the main projector (master projector) project the same patterns like the master projector.

Mode options:

  • Normal scanner mode – creates emotionalizing beam shows and graphics projections
  • Burst Grating mode – the scanned pattern is multiplied many times and covers a wide range
  • 3D Effect mode – creates a great 3D-looking effect on the scanned pattern
  • Radial Pattern Effect mode – a pattern is displayed in the center, the effect shows a multitude of this projection in circles around the center projection
  • Line Grating mode – a pattern is displayed multiplied in a line

Computer control:

The Laserworld PRO-800RGB has an ILDA interface for professional computer control. Thus own or pre-programmed laser shows can be displayed by use of a laser control software, e.g. Laserworld Showeditor.

DMX Mode:

Through DMX preset patterns, like waves, tunnels, circles etc. can be projected in different colours and at various speed.

Stand-alone Mode:

The laser system has an Stand-alone mode, which runs the pre-programmed patterns automatically.

Sound-to-light Mode:

If the Sound-to-light Mode is active, the laser system projects according to the sound. The microphone sensitivity can easily be adjusted at the rear side of the projector.

SD Card:

The Laserworld PRO-800RGB has an integrated SD card slot (a SD card is included in the delivery). It allows saving patterns, animations or shows as .ILD files on the SD card and running them at the projector. This option makes the use of this show laser system very flexible and independent of computer control.

Laserworld Showeditor FREE:

Laserworld Showeditor FREE is a free laser show software for creating own frames, figures, shows and for exporting them to ILDA (*.ild) format. It is possible to export these files to a SD card and to use it with integrated SD card slot at the Laserworld PRO-800RGB. 

Master-Slave Mode:

Next to the modes mentioned above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX to a main projector (master projector) project the same patterns like the master projector.

This laser device has a LCD display as well as menu buttons at the rear side providing a variety of features like setting the modes, grating effects, animations, colours, music sensitivity, etc..

In addition to the power connection socket and an on/off button there are interfaces for DMX in and out, ILDA in and out and for Interlock connection. An integrated key switch prevents the laser system against unauthorized use. The Laserworld PRO-800RGB is equipped with a beam block “Scan Fail Safety“, which can be switched on/off on the back panel as well. In active state, this prevents the laser from projecting single beams.

Finally a microphone for the music mode and a special loop for a safety cord have been integrated.

IR Remote Control:

An IR remote controller, included in the delivery, allows different settings like modes selection, speed control, run specific patterns etc… The IR LED at the front side flashes when receiving commands by the controller. The IR control is ideal when the projector is mounted on a truss etc. difficult to reach.

The rugged housing of the Laserworld PRO-800RGB is very compact and has dimensions of only 23.5 x 20.5 x 16.5 cm (W/B/H). A special feature of the housing is the mounting bracket that allows to fasten the unit in about 360° turns around the mounting axis of the bracket. This feature makes a fixed installation very easy.

The Laserworld PRO-800RGB is equipped with red and blue diode laser modules and a green DPSS laser module. The red diode has a wavelength of 637 nm for very good visibility at great beam specifications. Together with the green DPSS laser module with a wavelength of 532 nm and the royal-blue diode laser module with a wavelength of 445 nm the laser sources create brilliant colors and form a powerful source for the Laserworld PRO-800RGB.

The projector has good beam specifications with a beam diameter of about 3 mm and beam divergence of about 1.3 mrad (full angle). At the same time it offers a galvo system with up to 40 kpps with a max. scan angle of 40° and a deflection angle for the grating effects of up to 80°.

Laserworld Pro 800 RGB

    • Total Power typical: 800 mW
    • Guaranteed power: 700 mW
    • Power Red: 120 mW / 637 nm
    • Power Green: 120 mW / 532 nm
    • Power Blue: 460 mW / 445 nm
    • Beam Specifications: ca. 3 mm / ca. 1.3 mrad
    • Laser Sources: Diode, DPSS Laser
    • Laser Class: 4
    • Operation Modes: auto, music, DMX, ILDA, master-slave, SD Card
    • Scanner: Galvo system, up to 40 kpps@4°; additional effects gratings and glass effects
    • Scan Angle max.: 40° max. / 80° for glass effects
    • Basic Patterns: >200 Patterns (layers, tunnels, fences, waves etc.; grating & 3D effects)
    • Accessories: power cable, remote control unit, SD Card, manual, interlock connector, key, Laserworld Showeditor FREE
    • Power Supply: 85V – 250 V AC
    • Power Consumption: 50 W
    • Dimensions: 235/205/165 mm
    • Weight: 4.45kg

    See more at –

bottom of page